Links

Accessories

ACCESSORIES FOR COMCO MICROBLASTER RANGE

Below are details of accessories available for the Comco Microblaster, Directflo and Powerflo range.

MB4320-1 workstation magnifier for better visibility working on small parts Workstation / Cabinet Magnifier MB4320-1 Available for all the micro-abrasive blaster cabinets or anywhere good visibility is needed is the MB4320-1 Magnifier. This allows you to see even the smallest parts with ease. The magnifier window attaches directly to the outside of the work station window with Velcro for easy removal. It provides 2.4X magnification, with a large lens and a wide field of focus, giving excellent visibility.

Touchstart^TM Option (Factory Install only) Originally designed for use in confined area's where using a footswitch was impractical, the Touchstart^TM handpiece allows easy switching of the abrasive and is ideal for remote or difficult to reach areas.

Window Protection Shields. A common complaint about blasting inside any workstation is the frosting on the window caused by abrasive ricochet. For safety reasons only tempered glass should be used in your workstation, but that makes it expensive to replace. With our VisionPlus Window Shields you can protect a new window from excessive abrasive damage for a fraction of the cost of a replacement window. The shield adheres to the inside of the workstation window without the need for glue or adhesives - installation is clean and easy. When abrasive particles bounce back against the window, the shield absorbs the force of the abrasive and protects the glass underneath from frosting. When the shield begins to frost, you simply peel it off and install a new one. Available in packs of 3 (WS2279-3) or 10 (WS2279-10).

Constant Bleed option (Factory Install only)

Consistent operation of the MicroBlaster requires very clean, dry compressed air. This can be easily achieved with the proper dryer installed on the air line. A more difficult task is controlling the environment where the blasting occurs. Often it can be very wet and dirty, as in the case of hypodermic needle production facilities. To keep the contamination from clogging the nozzles we have developed a Constant Air Bleed Option.

The constant air option functions alternately with the pinch valve. When the machine is turned on clean air immediately begins flowing to the nozzle. As soon as the abrasive stream is activated the bleed turns off. The constant flow of air out to the nozzle keeps contamination from plugging into the nozzle and restricting the abrasive flow.

Blast Timer Option (Factory Install only)

Ring Nozzle

Wire Stripping Nozzle Ring (In Stock and on Demo - please contact for details)

Nozzle Adaptor For Directflo / Powerflo. All the standard microblaster nozzles can be used on the larger Directflo and Powerflo models by use of the PF2044 adaptor.

Nozzle Splitters run two to four nozzles from a single blaster (Directflo and Powerflo). Ideal for automation projects or specialist applications where two or more blast nozzles are required.

Spares Kits & Commonly used parts. We offer full backup support and advice for the whole Comco range of equipment, if you have a problem with your blaster we can offer technical support, we hold most common spares in stock and offer a repair/refurbishment service.

Media we supply a huge range of abrasive blast media for microblasting, from sodium bicarbonate to walnut shell, plastic, glass bead, silicon carbide and aluminium oxide is a wide range of sizes.

Nozzles. A wide range of nozzle sizes and configurations are available. The type of nozzle selected can vary on the application, media, size of area that needs to be abraded etc. All nozzles are fabricated from the hardest grade of long wearing tungsten carbide bonded into aluminum holders. Most popular sizes are nearly always available from stock. Also available from Comco are the SW range of nozzles suitable for SWAM & Crystal mark abrasive blast systems.

Tank Extenders. The powder capacity of a standard Microblaster Tank is equivalent to 2 lb of aluminum oxide. Tank extenders are available that double or tripple the powder capacity. Available for both the Microblaster Range (Double : MB1456-1, MB1456-3 (ACME thread). Tripple : MB1456-4) and the Directflo/Powerflo blasters.

High Pressure Models For special applications, single and dual tank Microblasters are available in High Pressure Models. The higher air pressure provides an increase in cutting action, which enables the abrasive stream to penetrate thick compounds and coating more efficiently.

Air Dryers. Vital for making sure your air is dry when running compressed air for fine abrasive blasting. We offer the AD5100 range of desiccant charge air dryers or the AD5300 series for heavy duty or long term use.

Dust Collectors. We provide a range of Dust Collection and Extraction systems, primarily for use with the Comco Micro-abrasive blast systems we supply, although, if you need any kind of fume or dust extraction, please contact us.

Workstations. A good workstation is essential for Microabrasive blasting to confine media dust for easy removal by the dust collector and provide an illuminated work area. We offer a wide range from small bench top sizes to large fully integrated cabinets and dust collectors, custom sizes can also be configured.

03/09/2010 09:06